Understanding the Tesla Model S Performance Motor

  Ganger 494,112

WeberAuto

2 måneder siden

Join me for a deep dive into the details of the 18,000 RPM performance rear motor and drive unit from a 2015-2016 Tesla Model S P90D. This drive unit is similar to the one used in the 2017-2020 P100D. The video is divided into four sections showing: 1. The motor and gears. 2. The high-performance bearings. 3. The lubrication system. and 4. The cooling system.
CORRECTIONS:
Thank you to everyone for catching my errors. There are always errors ;)
1. The Nissan Leaf ring gear is held on with 8 bolts, not 6.
2. The fluid in this drive unit is Dexron 6 transmission fluid.
3. Induction motor rotors do not have poles, just the stator. The 60 slot stator has four poles.
4. Silicon Nitride is a ceramic material.
TIMELINE:
0:00 Start
0:10 Introduction
1:35 Gearbox housing
2:10 Video Section 1 - Gears and Motor Rotor
2:45 The giant differential ring gear with 16-bolts!
4:20 The giant differential case bearings
4:50 The differential case speed at 250 km/h (155 mph) = 1841 RPM
5:15 MUST SEE Comparing the Tesla 213mm x 50mm. ring gear to a Chevrolet Bolt EV and Nissan Leaf EV
5:40 A Chevrolet Bolt EV differential 198mm x 34.3mm ring gear with 12-bolts.
6:10 A Nissan Leaf EV differential 200mm x 32mm ring gear with 8-bolts!
7:30 The Counter Shaft (Jack Shaft) with 25 pinion gear teeth. 78/25 = 3.12:1 Gear ratio from countershaft to the differential case
8:50 The countershaft speed at 250 km/h (155 mph) = 5743 RPM
9:30 The motor shaft with 25 teeth drives 78 teeth on the countershaft for another gear reduction of 78/25 = 3.12:1
10:08 The motor shaft speed at 250 km/h (155 mph) = 17,919 RPM
11:20 See all three gears in the reduction gearbox with an overall gear reduction of (78/25) x (78/25) = 9.7344:1
12:05 MUST SEE The AC Induction Motor Rotor with 74 bars
13:25 Motor specifications for power, torque, and gear ratio
15:00 MUST SEE Ceramic Bearings (Silicon Nitride) on the rotor from the SKF Group (skf.com)
16:22 MUST SEE Close up view of silicon nitride bearing
18:20 The motor rotor speed sensor reluctor wheel (tone ring)
19:22 Must SEE The rotor installed on the drive gear and the functioning gearbox
20:18 Video Section 2 - Specialized Bearings
21:21 The 60 slot four-pole stator and housing
23:05 The oil pump and how it is overdriven by the differential ring gear 23/78 = 0.2948:1 gear ratio (3.339 times faster than the ring gear)
23:55 MUST SEE The function of the oil pump (it may surprise you)
26:27 Motor shaft bearing reference speed and limiting speeds
27:30 How to run bearings at higher speeds than their limiting speeds
29:54 Video Section 3 - Lubrication
30:25 Drain and fill plug locations
30:50 Gearbox vent and inverter vents
31:05 Sport model label
31:39 MUST SEE Four different sealed areas in the drive unit
32:46 Video Section 4 - Cooling System
33:30 MUST SEE The coolant inlet port and the two paths coolant takes
33:53 Up for rotor cooling and gearbox cooling
35:03 Down for stator and inverter cooling
36:05 Coolant from the rotor moves to the gearbox heat exchanger and the outlet port
37:25 Stator temperature sensors
38:10 Coolant from the stator to the inverter coolant passages
38:28 Stator coolant temperature sensor
38:35 MUST SEE Insulated-Gate Bi-Polar Transistor (IGBT) module coolant passages and flow through gearbox passages
40:34 Inverter coolant outlet temperature sensor
40:45 The gearbox oil-to-coolant heat exchanger
41:38 Coolant outlet port to coolant pump and on-board charger module under the back seat.
41:55 Drive unit cooling system summary
43:04 IGBT inverter modules installed and inverter cover
43:40 High voltage battery cable connections and low voltage connections at the inverter
44:35 Video summary
ABOUT US
Weber State University (WSU) Davis Campus - Automotive Technology Department - Advanced Vehicles Lab. A technical description and demonstration of the Tesla P90D Rear Drive Unit (RDU). We teach current vehicle technologies to our automotive students at Weber State University and online. For more information visit: www.weber.edu/automotive
This video was created and edited by Professor John D. Kelly at WSU. For a full biography, see www.weber.edu/automotive/J_Kelly.html
Visit my other youtube channel nowindow.info to see the amazing NVH app for vibration diagnosis!
ADDITIONAL TRAINING FOR YOU
Join us for hybrid and electric vehicle training with two online courses and in a 5-day on-campus boot camp with Professor John D. Kelly. See www.weber.edu/evtraining
DONATE TO OUR DEPARTMENT
Please consider a donation to the Department of Automotive Technology at Weber State University here: advancement.weber.edu/Automotive

Kommentarer
Aravinth Kumar
Aravinth Kumar 16 timer siden
6:20 Nissan leaf's differential ring gear has 8 bolts instead of 6
Mitch Batten
Mitch Batten 16 timer siden
After watching this well delivered video I almost feel like I could be expecting a Certificate of Competency in the mail. Excellent job.
Puffers Paradise
Puffers Paradise Dag siden
Love the video I wish somebody would help this guy out with his breathing problems
Americannovice Twocentnovice
Americannovice Twocentnovice Dag siden
If the bearings were submerged in oil, a pump wouldn’t be needed.
Americannovice Twocentnovice
Americannovice Twocentnovice Dag siden
Silicone bearings? Raw materials only found on Mars. No wonder why Elon wants to go to Mars.
Americannovice Twocentnovice
Americannovice Twocentnovice Dag siden
I’m sixty years old and feel like a 18 year old kid back in my automobile mechanic class in the 1980’s.
Americannovice Twocentnovice
Americannovice Twocentnovice Dag siden
The motor for the Cybertruck must be twice as big as this motor for the model S.
PERRY JURGENS
PERRY JURGENS Dag siden
Wonderful teach-out - thanks!!!
Johan Kuhn
Johan Kuhn Dag siden
Silicon nitride IS a ceramic ;)
Johan Kuhn
Johan Kuhn Dag siden
@WeberAuto haha no problem, anyways really great video 👍
WeberAuto
WeberAuto Dag siden
Yes, thank you. I was wrong
Turre Tuntematon
Turre Tuntematon Dag siden
Well done! I would like to see the Plaid plus motor after it’s launched. Must be crazy! 😊
My Nguyen
My Nguyen Dag siden
Watching it incoperate with my design. thanks
Mr Pangy
Mr Pangy Dag siden
Great job. I would love to see complete comparisons to the competition.
Hello Dolly
Hello Dolly 2 dager siden
I believe those knobbly heat exchangers are called pin-fins. Thank you for a great tear-down.
Avelino Goncalves
Avelino Goncalves 3 dager siden
Nissan with 8 bolts...wight?
WeberAuto
WeberAuto 2 dager siden
@Avelino Goncalves Thank you
Avelino Goncalves
Avelino Goncalves 2 dager siden
@WeberAuto After, I saw your acknowledge. Thank you for your care! BTW...great video!! Mainly because you showed that there are fluid to be exchanged ate roughly every 100K miles, top at those loads! But Dextron knows it better!
WeberAuto
WeberAuto 3 dager siden
Yes, I was wrong. Thanks
Ayoub Boulehfa
Ayoub Boulehfa 3 dager siden
Excellent video
WeberAuto
WeberAuto 3 dager siden
Glad you liked it
Didža Nazis
Didža Nazis 4 dager siden
Damn, those bearings!
WeberAuto
WeberAuto 4 dager siden
I thought the same thing
Johan Grimm
Johan Grimm 4 dager siden
Hi prof. Kelly. Very interesting! Thank you! Have you seen this (deep dive but very short) nowindow.info/cloud/video/nKaIk26Mq22IoKM.html
Philip Quinlan
Philip Quinlan 5 dager siden
Excellent presentation. Thank you.
WeberAuto
WeberAuto 4 dager siden
Glad you enjoyed it!
Mariusz Zaleski
Mariusz Zaleski 5 dager siden
Another Wow!. High quality material. Thank you for sharing
WeberAuto
WeberAuto 5 dager siden
Glad you enjoyed it
Sam Ehlers
Sam Ehlers 5 dager siden
Thanks so much!
WeberAuto
WeberAuto 5 dager siden
You're welcome!
Rudolf Wickond
Rudolf Wickond 7 dager siden
250 km/h ? That's fast enough on the Autobahn ... unless someone is in a hurry.
WeberAuto
WeberAuto 5 dager siden
True, Thanks for watching
Amundsen
Amundsen 8 dager siden
Wow , excellent break down and analysis, SKF is a world leader in bearing technology, and the engineering and sophisticated machining required in this 500Hp power train is quit impressive to say the least. Fantastic explanation.
WeberAuto
WeberAuto 7 dager siden
Thank you very much
Greatest Evar
Greatest Evar 8 dager siden
bet that motor survived the fire just fine.
WeberAuto
WeberAuto 7 dager siden
Everything survived that was not plastic or nylon
JagiChan
JagiChan 8 dager siden
Wow, that is some serious engineering; and you did a fantastic job in explaining the whole drive train and the various components. Appreciate the amount of time and effort you dedicated to making such a great video.
WeberAuto
WeberAuto 8 dager siden
Thank you very much
Learn Progress
Learn Progress 8 dager siden
Is the lucid are motor better ?
WeberAuto
WeberAuto 8 dager siden
I haven’t seen one yet
Lucian Mihai
Lucian Mihai 8 dager siden
Would have been interesting to see the winding and inside of the rotor
WeberAuto
WeberAuto 7 dager siden
Thanks for watching
Lucian Mihai
Lucian Mihai 8 dager siden
The bearing technology is that used in the CNC machines spindle.ceramic are the best and can rotate up to 18000 rpm. They limited it under 18000 in order not to have surprises.
WeberAuto
WeberAuto 8 dager siden
Thank you for the information
T. W.
T. W. 9 dager siden
You can actually hear the motor and transmission whine if you sit in the rear seats on Tesla Model S P series cars when driving top speed on the autobahn.
WeberAuto
WeberAuto 9 dager siden
Awesome!
Michael Jennings
Michael Jennings 9 dager siden
to start, its a rotor not a motor
WeberAuto
WeberAuto 9 dager siden
Thanks, yes.
niceguy60
niceguy60 9 dager siden
Wait, the Model S has gears ???
WeberAuto
WeberAuto 9 dager siden
Four of them per motor
Vasile Cretu
Vasile Cretu 11 dager siden
On the third differential /gear box, there are 8 bolts, not six! ;)
WeberAuto
WeberAuto 11 dager siden
Yes, thank you. I was wrong
Hank Hall
Hank Hall 11 dager siden
SKF website (www.skf.com/caribbean/products/rolling-bearings/engineered-products/hybrid-bearings/permissible-speed) says rpm of silicon nitride bearings is limited, their equation gives rpm < 250000/(mean diameter of bearing). Estimating dimensions from your video it appears to me that the 17,900 rpm you mention for the motor is much higher than this limit. Correction: this comment is for grease lubrication.
WeberAuto
WeberAuto 11 dager siden
Thanks, I too was confused at first, but then I found the section of the catalog explaining how to safely exceed those limits. Thanks for watching
Aaron Schwarz
Aaron Schwarz 11 dager siden
Thats a very complex cooling system // but keeping electronics & transmission oil cooler makes both last longer //
WeberAuto
WeberAuto 11 dager siden
Yes it does
Aaron Schwarz
Aaron Schwarz 11 dager siden
20:16 there is something magical, no rare earths (china controls) permanent magnets (NdFeB etc) // induction motors are cooler than IPM for this specific reason & can be much much less expensive to make //
WeberAuto
WeberAuto 11 dager siden
Thanks for watching
Huw Williams
Huw Williams 12 dager siden
On the latest models there's something called the 'Octovalve' to manage the cooling systems as I understand it. It would be interesting to see how that works, because it is apparently unique to Tesla.
WeberAuto
WeberAuto 12 dager siden
Yes, coming soon. Thanks for watching
your wife's boyfriend
your wife's boyfriend 13 dager siden
Wow such a simple motor.
WeberAuto
WeberAuto 12 dager siden
It sure is! Thanks for watching
your wife's boyfriend
your wife's boyfriend 13 dager siden
Why didn't they just use 2 gears? 😐 why have not just have the differential gear contact the motor gear directly? Its both 78/25 isn't it?
your wife's boyfriend
your wife's boyfriend 13 dager siden
@WeberAuto so basically just adjusting gear size will increase acceleration & torque?
WeberAuto
WeberAuto 13 dager siden
It would need to have gears with sizes relative to being in first gear on a chain driven bicycle. The gear that turns the wheel would have to be gigantic to get the same gear ratio as we have now with two sets of smaller diameter gears.
your wife's boyfriend
your wife's boyfriend 13 dager siden
@WeberAuto how? Why? I don't understand 😕
WeberAuto
WeberAuto 13 dager siden
It keeps the gearbox size smaller
your wife's boyfriend
your wife's boyfriend 13 dager siden
If less gear = more torque, why not just use 2?
Buzz Pedrotti
Buzz Pedrotti 13 dager siden
Fascinating. Thanks.
WeberAuto
WeberAuto 13 dager siden
Glad you enjoyed it
Jon-William Murphy
Jon-William Murphy 13 dager siden
Crazy to me that the stator is welded to the other drive unit housings. I'm thinking about eccentricity, warp and tolerance issues, how did they get that to work? At 39:10, I'd call those pin fins. But buttons is definitely cuter.
WeberAuto
WeberAuto 13 dager siden
Good points, pin fins does sound better than buttons, lol, thank you!
THE16THPHANTOM
THE16THPHANTOM 14 dager siden
he uses mixed metric and imperial units... that's kind of a super power(to me). i could never get the feel of size with out translating one to the other.
WeberAuto
WeberAuto 13 dager siden
Thanks for watching
kyimedical
kyimedical 14 dager siden
You can call nodule for those aluminium lump to increase surface area of coolant chamber ,
WeberAuto
WeberAuto 14 dager siden
Thanks
Kimche TV
Kimche TV 14 dager siden
PREPARE SHIP FOR LUDICROUS SPEED...lmfao i say that every time i drop the hammer...
WeberAuto
WeberAuto 14 dager siden
Lol. Thanks for watching
A B
A B 15 dager siden
Damn i wanna watch but his breathing is so disturbing to hear omg.
WeberAuto
WeberAuto 14 dager siden
Thanks for the feedback
שמעון קופפרמן
שמעון קופפרמן 15 dager siden
I must mention that I enjoyed every second of your video!! You explain excellently (even though I do not really speak English)... I'm glad you're recording with a microphone at a constant distance from your mouth - you sound great! And the video is really good and clear. Your effort and investment is evident in every detail! What could I have asked for more? Wish you the best! And glad to see such videos. I also sent to some friends.
WeberAuto
WeberAuto 14 dager siden
Thank you very much
craigslist04
craigslist04 15 dager siden
John, another well-done presentation with great lighting and camera angles. You and Jack Rickard would have made for an awesome collaboration.
WeberAuto
WeberAuto 14 dager siden
Thank you very much
Fedupwithfed forever
Fedupwithfed forever 15 dager siden
So what ......I..... Will say ...as much as I'm against tne Uber lib Elon Musk and his TESLA....I DEFINITELY WILL...praise his company for his Quality that's put into the product his products......!
WeberAuto
WeberAuto 15 dager siden
Thanks for watching
sarastro60
sarastro60 17 dager siden
Mr. John Kelly, I am writing to you from Argentina. I thank you for such a didactic explanation of the operation of so many mechanical and electronic-mechanical systems. I would like to know what is the voltage in volts and what capacity in ampere hours of the Tesla battery output which you refer to as high voltage. Thank you very much and best regards.
WeberAuto
WeberAuto 17 dager siden
You are very welcome. The fully charged battery is about 400V DC. It is a 90kWh battery, so 90,000 Watts / 400 V = 225 Ah
Vita Quasus
Vita Quasus 17 dager siden
Best explanation of Tesla Motor I have ever seen. Thanks for this, it was informative and succinct.
WeberAuto
WeberAuto 17 dager siden
Glad you enjoyed it!
TIYOL56
TIYOL56 17 dager siden
this is goood stuff.
WeberAuto
WeberAuto 17 dager siden
Thank you
Wolverine Windsor
Wolverine Windsor 17 dager siden
Magnificent video
WeberAuto
WeberAuto 17 dager siden
Thank you
Brian Fretwell
Brian Fretwell 18 dager siden
I keep wondering what performance S performance. All motor perform so I can't get it.
WeberAuto
WeberAuto 18 dager siden
Thanks for watching
THE ELECTRIC SIDE OF THINGS
THE ELECTRIC SIDE OF THINGS 18 dager siden
Thank you for such a great video you explained it very well and I enjoyed watching the passion that you have for this electrical vehicle
WeberAuto
WeberAuto 18 dager siden
Glad you enjoyed it. Thanks for watching
Greg Hoyle
Greg Hoyle 20 dager siden
Why doesn’t this require any routine maintenance?
WeberAuto
WeberAuto 17 dager siden
The magic of marketing
Mingyar
Mingyar 20 dager siden
Tesla are over engineer. Just bought more stocks after watching this video
WeberAuto
WeberAuto 17 dager siden
Thanks for watching
Old Skeptic
Old Skeptic 20 dager siden
... with professional background in Mechanical Engineering and Electronics I would like to thank you for this majestic presentation of the emerging technology... The makers of this car could have done it in a 'flashier' manner, but not with such a careful, detailed approach you have employed here.. Thank you, Sir..
WeberAuto
WeberAuto 17 dager siden
Thank you very much
tadeusz czachor
tadeusz czachor 21 dag siden
best videos
WeberAuto
WeberAuto 21 dag siden
Thanks for watching
Kristian Jonsson
Kristian Jonsson 21 dag siden
Truck bearing on a passenger car differential!
WeberAuto
WeberAuto 21 dag siden
Thanks for watching
Chrisso
Chrisso 21 dag siden
Wow and wow again! Does this professional professor know his stuff! Truly an icon on teslas and other motors i would have to say! Truly professional! Aussie Chrisso 🥇🏆
WeberAuto
WeberAuto 21 dag siden
Wow, thanks!
fawzy moussa
fawzy moussa 21 dag siden
thank you , you are great,
WeberAuto
WeberAuto 17 dager siden
So nice of you
Xavier Garonnat
Xavier Garonnat 22 dager siden
Great video. Is it the same motor or at least same technology on Model 3 ? If yes on which version/year ? Thanks.
WeberAuto
WeberAuto 22 dager siden
Not for the rear motor of the model 3, this is different. The front motor of the Model 3 is similar to this one, but much smaller.
miguel goizueta
miguel goizueta 22 dager siden
Whoever designed this, deserved....What ???
WeberAuto
WeberAuto 22 dager siden
Thanks for watching
Pulkit Jain
Pulkit Jain 22 dager siden
Great. Now I just have to figure out how to make rest of the car!
WeberAuto
WeberAuto 22 dager siden
LOL, yes, me too
Richard Wallinger
Richard Wallinger 22 dager siden
My 1950 Westland Scout helicopter gearbox also used spray lubrication for the gears . I adopted this SECRET lubrication on my radio controlled model turbine helicopter .. Originally I attempted to tun oil bath lubrication which effectively fried the oil and overheated the gears due to hydraulic drag . Great video and super professional presentation .
WeberAuto
WeberAuto 22 dager siden
Very interesting, Thanks for watching
watchinglosersagain
watchinglosersagain 22 dager siden
So what he is saying at the beginning is that Tesla's balls are bigger than everyone else's.
WeberAuto
WeberAuto 22 dager siden
LOL, Thanks for watching
Petter Nygaard Hansen
Petter Nygaard Hansen 23 dager siden
Very good! My Tesla do 0 to 100km/h on 2,9 sek. No overheat, no vibrations, just 275km/h !
WeberAuto
WeberAuto 23 dager siden
Very cool!
René V1971
René V1971 23 dager siden
Very interesting and nicely explained!
WeberAuto
WeberAuto 23 dager siden
Many thanks!
Mike Nelson
Mike Nelson 23 dager siden
Thank you for this enjoyable video . A clear presentation. I am in the process of expanding my limited knowledge and understanding of how EV's work and are built. This is a bit difficult for an old fart like me , but very, very, interesting and enjoyable journey. So, again, from an old bloke in Australia, thanks.
WeberAuto
WeberAuto 23 dager siden
Thanks for watching!
Gsacni
Gsacni 23 dager siden
Thank you for an excellent presentation. Well done! It does however begs the question.... how did the car catch fire..? Was it related to the electronics and/or overheating of something in the motors..?
WeberAuto
WeberAuto 23 dager siden
Thanks, I do not know
Gary Eisenzimmer
Gary Eisenzimmer 24 dager siden
Geart presentation.
WeberAuto
WeberAuto 23 dager siden
Thank you
Girth Quake
Girth Quake 24 dager siden
I'll be super interested to see the internals of not only the front motors, but also the core differences between the SynR Model 3 motor and the permanent-magnet based S motors. Great to see these layed out like this; I see where the motors needed "refinement" based on secondhand details of their performance limitations and where the coolant would leak prior to those bearings being replaced with those ceramics.
WeberAuto
WeberAuto 22 dager siden
No, the AWD model 3 still has an induction motor in the front. The model S still has an induction motor in the rear. I think they use the induction motors for maximum performance and the PM Synchronous reluctance motors for economy. I suspect they can use just one motor during steady state cruising. I am still investigating that theory.
Girth Quake
Girth Quake 22 dager siden
@WeberAuto Really? I wonder then if Tesla has completely switched motor production to a SynR type of AC motor; makes sense for economies of scale and parts sharing.
WeberAuto
WeberAuto 23 dager siden
Thank you. It is my understanding that the 2019+ Model S front motor and the Model 3 rear motor are the same unit.
Not The weeknd • 25 years ago
Not The weeknd • 25 years ago 24 dager siden
I will always much rather prefer the classic petrol/diesel engines, I can’t get enough of carburetor technology.
WeberAuto
WeberAuto 24 dager siden
Thanks for watching
Jorge Suarez
Jorge Suarez 24 dager siden
Good info. Your providing an incredible resource for us techs in the field. What do you think about the GM 2ml70 ECVT transmission?
WeberAuto
WeberAuto 24 dager siden
Thank you. It looked on paper, but it was so heavy that it almost made the whole hybrid project useless. They told us in the factory training class in Burbank, CA that they had to add aluminum body panels and improve aerodynamics to get an actual improvement in fuel economy compared to the non-hybrid.
Richard S
Richard S 24 dager siden
Very, >Excellent< explanation of this Model S Performance Motor..
WeberAuto
WeberAuto 24 dager siden
Thank you very much
MFA
MFA 25 dager siden
28:28 the ball's expand... can cope with that...there are only 2 of them...
WeberAuto
WeberAuto 25 dager siden
Thanks for watching
Krzywoprostydezerter
Krzywoprostydezerter 26 dager siden
They could use ceramic bearings because it is an electric motor, there are no vibrations or any loads from the crank and piston system. They have a higher allowable RPM and generate much lower rolling resistance. The density of the oil may be lower, so it is easier to cool it down. This is a well-engineered engine design. For maximum performance, the reducer also uses ball bearings, lower resistance and lower operating temperature due to lower pressures than tapered roller bearings. A nice thought-out drive ... simply. Great explanation, and great video Professor. Thanks. Greeting from Poland
WeberAuto
WeberAuto 26 dager siden
Thank you and thanks for the information
FamilyFirstJ
FamilyFirstJ 26 dager siden
Incredible
WeberAuto
WeberAuto 26 dager siden
Thank you
Michiel van der Meulen
Michiel van der Meulen 26 dager siden
It feels strange two gears in the same box have an identical tooth count.
WeberAuto
WeberAuto 25 dager siden
@Michiel van der Meulen Yes, we call those "hunting gear ratios." That is very interesting
Michiel van der Meulen
Michiel van der Meulen 26 dager siden
@WeberAuto In printing machines one sometimes uses whole number gear ratios to have errors repeat over themselves. But then the consequences for wear and possible vibrations are taken for granted deliberately. Interesting.
WeberAuto
WeberAuto 26 dager siden
I thought the same thing. It works well
Kim Hansen
Kim Hansen 27 dager siden
Great video, even for a non-engineer.
WeberAuto
WeberAuto 27 dager siden
Thank you
CW Science Projects
CW Science Projects 27 dager siden
I have watched many of Professor Kelly's videos. They are well presented, informative and easy to understand. As a gear design engineer with many years experience on off-road vehicle gears I can make following comments 1. Model S final drive gear face width could be wider than required for durability or torque capacity. When the helix angle is low, more face-width is needed for higher overlap ratio and quietness when running (possible explanation) 2. Size of diff carrier bearings. Many times the half shaft spline size required for it's strength under side gear dictates size of bearings rather than load carrying capacity . Also the special bearing type might have a lower capacity than the standard type. Thus requiring a larger size bearing (possible explanation) Please continue making these videos - Good luck
WeberAuto
WeberAuto 15 dager siden
Thank you very much!
Bob de Bruin
Bob de Bruin 27 dager siden
Excellent quality video and content
WeberAuto
WeberAuto 27 dager siden
Glad you enjoyed it
James LaRoche
James LaRoche 27 dager siden
OooOoOooo! I clicked this super fast!
WeberAuto
WeberAuto 27 dager siden
Thank you for watching
Johnny Voo
Johnny Voo 27 dager siden
Isn't that eight bolts at 6:18
WeberAuto
WeberAuto 27 dager siden
@Johnny Voo Thank you
Johnny Voo
Johnny Voo 27 dager siden
@WeberAuto OK. Very good video. Thanks.
WeberAuto
WeberAuto 27 dager siden
Yes, I was wrong
turk 182
turk 182 28 dager siden
DID you read the small print? You are not aloud to open the gearbox. A Law suit is coming your way so make sure your hole is greased up good because you are in for a roller coaster of a ride.
WeberAuto
WeberAuto 27 dager siden
Lol. I guess not
Paul Keith
Paul Keith 28 dager siden
Two in a car, from different households, but not wearing masks. Different rules of course.
WeberAuto
WeberAuto 28 dager siden
Thanks for watching
Alouis Schäfer
Alouis Schäfer 28 dager siden
The quality of their Drivetrain Components set the standard for everybody else. I hope they will apply that to commercial vehicles in the future because that is where the focus of the EV World should be. There are some potential issues in my opinion: -The oilpump setup looks very flimsy and cheap compared to the other components. Also the lack of an actual oil filter should be noted down. Sure the magnet will catch most of the worn off metal but pretty much all modern transmissions have a dedicated oil filter so why not Tesla? -Having multiple compartments with different fluids in them is a potential weak point. So I hope Tesla did their homework and used long lasting high quality seals. Failing seals are the Achilles Heel of any vehicle.
WeberAuto
WeberAuto 28 dager siden
It is impressive. Thanks for watching
Henry Chen
Henry Chen 28 dager siden
I disabled my adblocker and watched the entire ad for you. Keep it up!
WeberAuto
WeberAuto 28 dager siden
Thank you!
Wilderness Music
Wilderness Music 28 dager siden
Maybe we should look at the bearings of the Kawasaki Ninjas of the year 2000. My 250cc Ninja had a redline of 14,000 RPM. 20 year old technology.
WeberAuto
WeberAuto 28 dager siden
Amazing technology! Thanks for watching
Steve Brewster
Steve Brewster 28 dager siden
Great detailed explanation for somethiing not many of us electron heads get a chance to pull apart. Thank you for the insights.
WeberAuto
WeberAuto 28 dager siden
Thank you very much
Darren Hwang
Darren Hwang 28 dager siden
1.25x speed playback is just right
WeberAuto
WeberAuto 28 dager siden
Thanks for watching
Brandon Yarber
Brandon Yarber 28 dager siden
8 bolts
WeberAuto
WeberAuto 28 dager siden
Yes, thanks, I was wrong
mdimascio
mdimascio 29 dager siden
Great presentation and detailed analysis!
WeberAuto
WeberAuto 29 dager siden
Much appreciated!
Sherman Morgan
Sherman Morgan 29 dager siden
I really enjoyed watching the video. Very well presented. Thanks for making this very informative video.
WeberAuto
WeberAuto 29 dager siden
Glad you enjoyed it!
D U V A C H
D U V A C H 29 dager siden
nowindow.info/cloud/video/gHWfYoSYe4hmmYk.html
Dessin animé
Dessin animé 29 dager siden
Excellent approch for E motors thanks . What does FSD tesla cars work ?
WeberAuto
WeberAuto 29 dager siden
Thank you. FSD is not my area of expertise.
Drone.Camera.Action
Drone.Camera.Action 29 dager siden
Would love to see a model 3/Y video to see the difference, especially as this is the future..
WeberAuto
WeberAuto 29 dager siden
Coming soon
Sanket Devle
Sanket Devle 29 dager siden
Very nice video with detail information about powertrain.
WeberAuto
WeberAuto 29 dager siden
Glad you liked it
Ancillary Sword
Ancillary Sword Måned siden
Incredibly informative!
WeberAuto
WeberAuto 29 dager siden
Thank you
John Henry Holiday
John Henry Holiday Måned siden
Would You buy a Tesla ???? Im tempted and Im not "green"
WeberAuto
WeberAuto Måned siden
Yes
John Henry Holiday
John Henry Holiday Måned siden
Awesome.... Tesla in theory could go forward and reverse at 155 MPH.... that could be really fun....
WeberAuto
WeberAuto Måned siden
Thank you. It would be fun
Garry Perrin
Garry Perrin Måned siden
Super cool, informative video Professor.
WeberAuto
WeberAuto Måned siden
Thank you!
2021 Tesla Model 3 Full Review
34:56
100 Rental Cars
Ganger 242 k
How to use a Transmission Dipstick
25:38
Can Nuclear Propulsion Take Us to Mars?
21:45
Real Engineering
Ganger 593 k
Electric Engine PRODUCTION - Audi e-tron MOTOR
15:21
GommeBlog.it: Car & Performance
Ganger 9 mill
Can Nuclear Propulsion Take Us to Mars?
21:45
Real Engineering
Ganger 593 k
Customizing a JUMBO Nesting Doll Set
17:44
Moriah Elizabeth
Ganger 2,2 mill
A BRAND NEW GAME SHOW IS BACK
32:31
Miniminter
Ganger 1,6 mill
My Thoughts on Reality Shifting
9:48
TheOdd1sOut
Ganger 9 mill